Yes, I looked up your 2020 North Trail 33BKSS and it is pre-wired for a Furrion backup camera like the # FOS43TASF that you referenced. view full answer...
You are correct. The Saris MHS Modular Bike Rack for 2 Bikes - 2" Hitches - Tilting, part # SAR73MR, will not work with your wife's Blix Aveny because the rear fender will interfere with the racks arms. Another reason it will not work is because it is not compatible with travel-trailers. However, the Yakima OnRamp Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount, part # Y36FR, is compatible with travel trailers.
It also comes with a ramp to help you load the heavier ebike. The... view full answer...
To get that third step the best option for you is the MORryde StepAbove RV Steps for 23-3/4" to 26-1/4" Wide Doorways - 3 Steps # MR98RR. This will attach to the floor just past your door frame and fold up into the trailer while not in use. view full answer...
I looked up the length of your Heartland 31BHDD North Trail 2013 and found that it's 36 feet long so for a cover similar to what you referenced that does fit that size you'd want the Adco Storage Lot Cover part # 290-74847 and you'd be set. view full answer...
The MORryde 14-3/4" Shock Absorbing Equalizers for Tandem Axle Trailers part # MR34AR will work great on a 2021 Heartland RV North Trail Travel Trailer and what I recommend using. They can then be combined with the MORryde Suspension Upgrade Kit for Tandem Axle Trailers part # MR46ZR for upgraded shackle straps and wet bolts. These equalizers are rated up to 8,000 lbs so they will work great on a set of 4,400 lb axles. view full answer...
The correct anode rod you'll need will be based on the water heater you have installed in your 2019 Heartland North trail. If you have a Suburban/Mor-Flo you would need the part # CAM11563 or if you have the more popular Atwood water heater you would want the part # CAM11553. We don't have a way to determine what water heater you have.
The tool you need is the part # CAM09883. view full answer...
The trailer hitch I recommend for a 2020 Subaru Outback Wagon is the Stealth Hitches Rack Receiver part # 391SUOB20 which once installed will be completely hidden behind the rear bumper therefore you will retain the same factory appearance as the vehicle would have had once rolled off the showroom floor. The Stealth Hitches Rack Receiver is a direct bolt-on fit with no drilling required. However, you will need to remove the rear bumper fascia but this only needs to be done once whereas... view full answer...
Thanks for reaching out!
To add a hitch to the back of your 2019 Heartland 24BHS you'll need to measure the distance between your frame and install one of our adjustable hitches. One of our more popular options is the Curt Adjustable Width Trailer Hitch Receiver # 13703 because it fits frames 22" - 72" wide and uses mounting brackets that fit a variety of frame styles.
Then when it comes to wiring I recommend adding the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector... view full answer...
The Rubber Wiper Seal and Bulb for RV Slide Out # SR98FR that you referenced installs with an adhesive backing that attaches to the RV frame that surrounds the slide out. There are quite a few different setups and ways it can install though so basically you are going to have to look at your setup and determine what you have to figure out out it would need to get removed and what would be the style you'd need to replace it with. All of our options are a stick-on style of install meaning... view full answer...
In order to find the correct replacement leaf spring for a trailer you first need to start by noting the type whether that be slipper or double eye. Then, you'll need to measure their unloaded length via jacking up the trailer. If the springs are worn they will measure longer than their replacement. Lastly, you will need to note the axle capacity which is found on the tag in the center of the beam. Please note, the number of leaves does not really denote capacity as leaves have different... view full answer...